How to adjust and lubricate your motorbike chain (and how often)
The chain transmits all the engine's power to the wheel. Badly tensioned or dry, it eats the drivetrain and is dangerous. Learn to lubricate and adjust it properly, step by step.
Written by Andrés Rendón
Founder and host of Somos Motor, June 11, 2026
The drive chain is one of the parts that suffers most and gets the least care. A dry or badly tensioned chain wears out fast, makes noise, saps power and, in the worst case, can jump off. The good news: looking after it is among the easiest and cheapest things you can do for your bike.
01How often to lubricate the chain
As a rule, every 500 to 1,000 km, and always after riding in the rain or washing the bike (water and cleaning products strip away the grease). If you cover a lot of kilometres or tour, make it a routine habit, almost like refuelling.
02How to lubricate the chain step by step
- Put the bike on a paddock stand so you can turn the rear wheel, or roll the bike forward bit by bit.
- Clean it first if it is very dirty. Use a dedicated chain cleaner and a brush. Never an aggressive degreaser that could damage the O-rings (the rubber seals that keep the internal grease in).
- Apply chain lube to the inner side while you turn the wheel, so that it reaches every link. A small amount, well spread.
- Leave it to settle for a few minutes so the lube soaks in before you ride. Wipe off the excess so it does not spatter the tyre.

03How to measure and adjust the tension
The correct tension is set by your manual: it is the slack (vertical play) the chain should have at its midpoint, normally between 2 and 4 cm. Neither too tight nor too loose.
- Measure the slack at the midpoint between the two sprockets, with the bike on the ground and no weight on it.
- If it needs adjusting, loosen the wheel axle nut and move the adjusters at the ends of the swingarm.
- Tighten both adjusters equally so the wheel stays aligned (there are reference marks on each side). A crooked wheel wears both chain and tyre.
- Tighten the axle to the correct torque and check the slack again.
A chain that is too tight is as bad as a loose one: it strains the bearings and can snap. If in doubt, leave it a notch looser rather than overtightened.
04The costliest mistake: letting it die
A neglected chain drags the front sprocket and the rear sprocket down with it. When one of the three parts wears out, all three are replaced together (the chain kit), because a new part running with two worn ones quickly gets ruined. That is why regular maintenance pays off so well: it extends the life of an assembly that is expensive to replace.
05When it is time to replace the kit
If the chain has seized links, “tight spots” as it turns, or if however much you tension it, it stays loose in some places and tight in others, it is stretched beyond use: time for a new kit. The same goes if the teeth on the rear sprocket are sharpened like a saw.
This goes hand in hand with the rest of the maintenance. If this helped, take a look at how to do the oil change and when to change the brake pads, and you will have the essentials covered. There is even someone who has built a system to tension it from your phone: we asked its creator about it in the episode on the May1ne invention. More guides in mechanics and maintenance, and we will let you know about each new one in the newsletter.
This guide is part of our complete motorbike maintenance guide, where you will find everything you should check and how often.
Frequently asked questions
How often should a motorbike chain be lubricated?
Every 500 to 1,000 km and always after riding in the rain or washing the bike. It is a quick job that greatly extends the life of the drivetrain.
What happens if I run the chain too tight?
It strains the swingarm and wheel bearings, increases wear and, in extreme cases, the chain can snap. Always adjust to the slack your manual specifies.
Can I use any grease?
Use a dedicated chain lube. Other lubricants fling off, attract dirt or damage the O-rings that seal the chain's internal grease.
Keep reading
More from the blog
November 9, 2026
Tyre checks before a long journey, and when to replace them
Before a long drive, check tyre pressure when the tyres are cold, using the figure for your load, and make sure the tread is above the 1.6 mm legal minimum.
November 9, 2026
Car maintenance checklist: what to check, how often and what you can do yourself
Oil and filters, tyres, brakes, coolant, battery, timing belt and the MOT: what needs checking, how often, which jobs you can do at home and which belong in a garage.
November 7, 2026
Car battery in winter: why it fails and how to test it
In the cold, a 12 V battery delivers less current just when the engine demands most to start, and it exposes the wear summer left behind. Which signs warn you, how to measure it with a multimeter, what changes with start-stop and how to avoid being stranded.